How to save money when replacing home wiring without sacrificing reliability

Replacing home electrical wiring is one of the most expensive stages of major repairs in an apartment or house. Against the backdrop of constantly rising prices for cable products and other components, the question of how to replace the wiring with minimal cash investment is becoming increasingly relevant.

In this case, you can’t just unreasonably remove certain elements or underestimate the cross-section of the wires, as this can lead to the fact that the installed wiring will be unreliable and will not provide full power to home electrical appliances. Therefore, we need to consider how to save money when replacing home wiring without compromising reliability, which we will discuss in this article.

The process of replacing wiring can be divided into three main stages:

• designing a future electrical wiring;

• selection and purchase of components, required tools and materials;

• installation of new wiring.

The cost of replacing the wiring in this case depends on who will perform all the work. The maximum cost will be in the case when all the work on replacing the wiring from the preparation of the project to the installation itself is carried out by an electrician.

At the same time, most likely, it will not be possible to save - single craftsmen or the corresponding organizations have fixed prices for all types of work, as well as their proven components, which they use when conducting replacement wiring to customers.

If all the work is done independently, then all the costs of replacing the wiring will only be for the purchase of the necessary components. In this case, you can save more than half, or even 2/3 of the amount that an electrician specializing in replacing wiring would take. But this is provided that if you have the required tool, knowledge and skills for the replacement of wiring.

The most difficult stage of installation work is strob preparation for laying cable lines, wiring places for mounting boxes for sockets, switches, intermediate junction boxes. In this case, it all depends on the material from which the walls are made.

If it is a plastered brick wall, then it is possible to do the work with a perforator and a chisel with a hammer. Also, it does not cause difficulties to install electrical wiring on the walls, which are planned to be sewn up with drywall.

But if you need to make shtrobs in reinforced concrete structures, then in this case you can not do without a specialized tool - chipper. In this case, it will be cheaper to use the services of an electrician to wall the walls than to purchase the appropriate tool. Moreover, the purchase of a chamfer for carrying out single operations is impractical.

It is also necessary to soberly assess your capabilities, as there is a high probability of making mistakes during the installation of electrical wiring. In the absence of practical skills in carrying out such work, such savings will result in even greater costs and in the end, you still have to use the services of an electrician to eliminate errors.

At the same time, the use of the services of electricians or relevant organizations cannot guarantee that the installed wiring will be reliable. Very often there are unskilled electricians who, when designing and installing electrical wiring, make a number of mistakes. Therefore, if it is decided to entrust all the work to the appropriate specialists, then it is necessary to choose those organizations or single electricians who have a good reputation.

Particular attention should be paid to the design of new wiring. Wiring cannot be replaced without preliminary calculations, drawing up the wiring diagram, selection of installation locations for various elements and routes for laying electrical wiring. If there is no relevant knowledge, then, accordingly, the design of future electrical wiring must be entrusted to an experienced specialist.

In the event that you still decide to save and design future wiring yourself, you need to adequately assess your knowledge. If there are doubts about the correctness of the chosen solution, then it is better to consult with a knowledgeable person.

You can study a lot of information on the issue of wiring replacement, but still make a gross mistake, which in the future will lead to the fact that the installed wiring will be unreliable and dangerous in operation. That is, when you have thought everything through, made a wiring diagram, consult a specialist to avoid possible problems.

The design phase is also most important in terms of saving. In this case, the savings consist in comparing different options for laying electrical wiring lines, relocating sockets and other elements and choosing the least expensive option.

The question is very important stock load, as in individual sections of the wiring, and the load capacity of the wiring as a whole.

On the one hand, the design of electrical wiring with a margin significantly increases its cost, but on the other hand, in the future, in the event of an increase in the load of electrical appliances, there will be no need to replace electrical wiring in certain areas. It is necessary to approach this issue as carefully as possible, having analyzed the relevance of the availability of stock in various sections of the wiring.

When the required cable length, the required number and types of sockets, switches, protective devices and other structural elements of electrical wiring are known, the question arises of where to get all this and which manufacturers to give preference to.

In this case, it is very important to choose the most optimal product in terms of price-quality ratio. You should not save money by purchasing cheap materials and components of dubious quality, as it is highly likely that they are not reliable enough. Such savings are contrary to the original installation of wiring replacement without compromising reliability.

In conclusion, we can conclude that you can save money when replacing wiring, but you need to do it wisely. As they say - saving should be economical.

Having decided to save on a particular wiring element, you need to think about how this can affect the reliability of the wiring, so that in the future such savings will not lead to even more waste. That is, in fact, you do not need to overpay the extra money, but do not buy frankly low-quality components.

The same applies directly to installation work - the desire to save money without having the appropriate skills to carry out work on your own will ultimately lead to even greater costs.